Deactivation of hydrodesulfurization catalysts during reactor startup

Metal sulfide catalysts for ultra-deep hydrodesulfurization of diesel generally lose a fraction of their catalytically active sites during reactor startup. The underlying mechanisms are discussed. A laboratory diagnostic tool consisting of three probe molecules is developed for testing metal sulfide catalysts' start-of-run (SOR) activity maintenance. It is found that a significant fraction of the active sites on a commercial supported catalyst are deactivated permanently, but this is not the case with a bulk metal sulfide catalyst. The SOR deactivation of the bulk catalyst is completely reversible, while that of the supported catalyst is partially reversible. The diagnostic tool may provide a basis for developing a high-throughput approach for evaluating and enhancing catalyst SOR stability, thereby increasing plant productivity.     

石墨烯热电器件栅控特性研究

为了获得一种稳定可控的能源，提出一种栅控石墨烯热电器件。通过对石墨烯通道的载流子输运机理的分析，获得了温度和栅压对通道电阻的影响。依据半经典Mott公式推导了石墨烯塞贝克系数的表达式，同时给出了石墨烯的电导率和热导率模型。最后通过有限元分析(FEA)建模获得不同栅压条件下的器件温度，当栅极电压V_B=0 V时，石墨烯热电器件热端和冷端温度差为30 K；当V_B=6 V时，最大温差达到50 K；当V_B=30 V时，最小温差只有10 K。结果表明，栅压对热电器件的性能有明显的调控性。该研究可为石墨烯热电器件的设计提供理论参考。     

Fabrication of Ti3SiC2-based pastes for screen printing on paper-derived Al2O3 substrates

This paper describes the development and fabrication of pastes suitable for screen printing process using Ti₃SiC₂ as the ceramic filler and ethyl cellulose as the binder. With the aim of obtaining high quality screen printed films, the influence of different amounts of Ti₃SiC₂ filler (20–40?vol%) and binder (0–5?vol%) on the rheological properties of the pastes was investigated. Samples with higher viscosity, such as pastes containing 30?vol% and 40?vol% Ti₃SiC₂ filler, regardless of the amount of ethyl cellulose, showed a higher printing quality compared to the samples with other compositions. The different paste compositions were screen printed onto paper-derived Al₂O₃ substrates containing 28.6 ± 4.8% open porosity and sintered for 1?h under an argon atmosphere at 1600?°C. X-ray diffraction (XRD) measurements and scanning electron microscopy (SEM) analysis showed that the sintered films contained TiC as a primary phase and Ti₃SiC₂ as a secondary phase. The partial decomposition of Ti₃SiC₂ after sintering can be attributed to residual carbon from the organic additives, which decreases the thermal stability of this material.     

Mullite-bonded SiC-whisker-reinforced SiC matrix composites: Preparation,characterization, and toughening mechanisms

A novel mullite-bonded SiC-whisker-reinforced SiC matrix composite (SiCw/SiC, SiC whisker-to-SiC powder mass ratio of 1:9) was designed and successfully prepared. Before preparing the composite, the inexpensive lab-made SiCw was first modified by an oxidation/leaching process and then coated with Al₂O₃. The kinetics results indicate that the oxidation process can be described by improved shrinking-cylinder models. The aspect ratio of SiCw improved after modification. Subsequently, raw materials with a SiC–SiO₂–Al₂O₃ triple-layered structure were obtained after the Al₂O₃-coating process and used as feedstocks during the subsequent hot-pressing sintering. Finally, the characterization of the composites indicates that the mullite-bonded sample performs better (relative density of 93.8?±?1.4%, flexural strength of 533.3?±?18.2?MPa, fracture toughness of 13.6?±?2.1?MPa?m^1/2, and Vickers hardness of 20.6?±?2.5?GPa) than the reference sample without the mullite interface. The improved toughness could essentially be attributed to the moderately strong interface bonding and effective load transfer effects of the mullite interface.     

一种分散在多孔碳上的碳包覆硅负极的制备及应用

硅负极具有高比容量的显著优势,其理论比容量（4 200 mA∙h/g）达到传统石墨负极的10倍以上,被认为是锂离子电池最有潜力的负极之一。然而,硅负极存在导电性较差、充放电过程中体积膨胀巨大等诸多问题,导致其循环性能较差,限制了大规模实际应用。本文提供了一种高性能硅负极的制备方法及应用,通过将硅负极分散在多级孔碳中,连同黏结剂聚丙烯腈涂覆在集流体上,再对极片进行热处理实现聚丙烯腈碳包覆,有效提高电极的整体导电性并能为巨大的体积变化提供空间,从而提升硅负极的大倍率性能和循环稳定性。     

Properties of multiple oxide-bonded porous SiC ceramics prepared by an infiltration technique

Multiple oxide-bonded porous SiC ceramics were fabricated by infiltrating a porous powder compact of SiC and alumina with cordierite sol followed by sintering at 1300-1400°C in air for 3 hours. The microstructures, phase components, mechanical properties, and air permeation behavior of the developed porous ceramics were examined and compared with materials obtained by the traditional powder processing route. The porosity, average pore diameter, and flexural strength of the ceramics varied from 33 to 37 vol%, ~12-14 μm and ~23-39.6 MPa, respectively, with variation in sintering temperature. The X-ray diffraction results reveal that both the amount of cordierite and mullite as the binder increased with increase in sintering temperature. In addition, it was found that the addition of alumina in powder form effectively enhanced the strength due to formation of mullite in the bond phase in contrast to the samples prepared without alumina additive. To determine the suitability of the material in particulate filtration application, particle collection efficiency of the filter material was evaluated theoretically using single collector efficiency model.     

铌对取向硅钢冷轧组织织构的影响

采用光学显微镜(OM)、电子背散射衍射(EBSD)等研究了铌对取向硅钢冷轧过程中的组织与织构的影响。结果表明:含铌正火板和不含铌正火板经冷轧后都是条带状组织,但含铌冷轧板在宽度方向更窄。铌元素的存在对织构也具有优化作用,经过中间退火后,含铌冷轧板二次冷轧织构得到明显改善,相较于不含铌二次冷轧板拥有强度较低的旋转立方织构以及强度较高的{111}<112>织构,其取向密度最高可达12.460。     

硅渣和玻璃粉直接烧结制备多孔材料的气孔结构与力学性能

以硅渣和玻璃粉为原料,采用粉体直接烧结法制备多孔材料,研究了烧结温度(700~900℃)、烧结时间(15~120min)和升温速率(10~100℃·min^-1)对多孔材料表观密度、气孔率、物相组成、抗压强度的影响。结果表明:气孔结构均匀性随烧结温度的升高而降低;表观密度随烧结温度的升高先减小后增大,随保温时间的延长而增大,随升温速率的增大而减小,气孔率的变化趋势与表观密度的相反;多孔材料的主要物相为玻璃相和硅、SiC、SiO2、Ca2Al2SiO7等结晶相,且结晶度随烧结温度的升高而降低;抗压强度随烧结温度的升高呈先增大后减小的趋势;当烧结温度为750℃,升温速率为30℃·min^-1,烧结时间为30 min时,多孔材料的主晶相为硅和Ca2Al2SiO7,抗压强度最大(1.60MPa),表观密度为0.43g·cm^-3,气孔率为80%。